{"product_id":"rotor-truing-fork-2-0","title":"Rotor Truing Fork 2.0","description":"\u003cp\u003eA disc rotor that's even slightly out of true rubs the pads at every revolution. You hear it as a whisper under braking; you feel it as a pulse in the lever. Rotors warp under heat-cycling, take a set after a crash, or pull sideways when the rotor bolts get an uneven torque sequence during install. The Rotor Truing Fork 2.0 lets you correct the warp without removing the wheel: multiple notches at different angles give you leverage at the exact point the rotor needs to bend, and the laser-cut tool-steel blade takes the workload without flexing.\u003c\/p\u003e\n\u003cp\u003eThe notches seat over rotors up to 2.4 mm thick, which covers every road and MTB rotor we've measured against the fork in the workshop. After laser cutting, the blade is heat-treated, which is the difference that matters in use: the slot edges don't deform under the leverage you have to apply to bend a rotor. The slot edges hold their shape under the leverage that would deform mild steel.\u003c\/p\u003e\n\u003cp\u003eThis is a workshop tool, not a trailside one. At 158 g and 190 mm long it lives on the bench (there's a hole on the back for hanging), and it works the rotor while the wheel is still in the dropouts. You isolate the bent section against a notch and apply leverage perpendicular to the disc face. Small corrections, checked against the caliper's pad clearance, until the rub clears.\u003c\/p\u003e\n\u003ch2\u003eSpecs\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eFunction: rotor truing fork for disc-brake rotors\u003c\/li\u003e\n\u003cli\u003eConstruction: laser-cut tool steel, heat-treated\u003c\/li\u003e\n\u003cli\u003eMultiple notches for engaging the rotor at different angles\u003c\/li\u003e\n\u003cli\u003eRotor thickness compatibility: up to 2.4 mm\u003c\/li\u003e\n\u003cli\u003e190 × 30 × 5 mm\u003c\/li\u003e\n\u003cli\u003e158 g\u003c\/li\u003e\n\u003cli\u003eIncludes a hole for workshop hanging\u003c\/li\u003e\n\u003cli\u003eArticle number: 1666-6\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eWhen truing is the right call\u003c\/h2\u003e\n\u003cp\u003eTruing has limits. A rotor that's been heat-cycled to discoloration in multiple spots is past saving; straightening it bends the metal back through grain that's no longer uniform. If the rotor is thinner than the manufacturer's published wear limit (Shimano's spec is 1.5 mm; check the stamping or spec sheet for your rotor), the answer is the same. That's a replacement, not a truing job. The fork is for the in-between case: a localized warp on a rotor that's otherwise within service spec.\u003c\/p\u003e\n\u003ch2\u003eBuilt in Zreče, Slovenia\u003c\/h2\u003e\n\u003cp\u003eUnior has been forging hand tools in Zreče since 1919, and sponsors professional road and mountain-bike race teams. The truing fork's laser-cut tool steel and heat treatment are workshop-grade decisions, not consumer-grade ones. You can tell the difference the first time you put load on the blade.\u003c\/p\u003e\n\u003ch2\u003ePro tip from our mechanics\u003c\/h2\u003e\n\u003cp\u003eAlways let calipers and rotors cool to ambient before truing. Hot rotors are softer and bend further than you intend, and a bent-too-far rotor is harder to true back than the original warp. Our disc-brake-rub guide covers how to tell whether truing will fix the rub or whether the rotor's already past the point where straightening helps: Fix disc brake rub →\u003c\/p\u003e\n\u003ch2\u003eFAQ\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eWhat tool do shops use to straighten a warped disc rotor?\u003c\/strong\u003e A rotor truing fork. The notches seat over the bent section at the angle you need, and the heat-treated tool-steel blade gives you the leverage to bend the rotor back toward true in small corrections, rechecking pad clearance as you go.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eDo I need to remove the wheel to true a disc rotor?\u003c\/strong\u003e No. The fork works with the wheel still in the dropouts: isolate the bend against a notch, lever perpendicular to the disc face, and recheck clearance. The notches fit discs as thick as 2.4 mm, road or MTB.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eShould the rotor be hot or cold when you true it?\u003c\/strong\u003e Cold, always at ambient temperature. A hot rotor is softer and bends more than you mean it to, and a rotor bent too far is harder to bring back than the original warp was to fix.\u003c\/p\u003e","brand":"Unior USA B2B","offers":[{"title":"Default Title","offer_id":46161526915308,"sku":"629938","price":23.77,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0464\/7708\/2777\/files\/1666_6_629938_image_1024-Square.jpg?v=1787170629","url":"https:\/\/b2b.uniorusa.com\/en-ca\/products\/rotor-truing-fork-2-0","provider":"Unior USA B2B","version":"1.0","type":"link"}